Datalogic Scanning QuickScan QD2100 User Manual Page 292
- Page / 320
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
284 QuickScan® QD2100
LED and Beeper Indications
INDICATION DESCRIPTION LED BEEPER
Power-up Beep
The imager is in the process of pow-
ering-up.
Imager beeps four times at highest
frequency and volume upon power-
up.
Good Read Beep
A label has been successfully
scanned by the imager.
LED behavior for this indica-
tion is configurable via the
feature “Good Read: When to
Indicate”
The imager will beep once at cur-
rent frequency, volume, mono/bi-
tonal setting and duration upon a
successful label scan.
ROM Failure
There is an error in the imager's
software/programming
Flashes
Imager sounds one error beep at
highest volume.
Limited Scanning
Label Read
Indicates that a host connection is
not established when the IBM or
USB interface is enabled.
N/A
Imager 'chirps' six times at the high-
est frequency and current volume.
Imager Active
Mode
The imager is active and ready to
scan.
The LED is lit steadily
a
a.
Except when in sleep mode or when a Good Read LED Duration other than 00 is selected
N/A
Imager
Disabled
The imager has been disabled by
the host.
The LED blinks continuously N/A
Green Spot is on
continuously
While in Stand Mode or Trigger
Object Sense mode the green spot
shall be on while in stand watch
state.
N/A N/A
Green Spot
a
flashes momen-
tarily
Upon successful read of a label, the
software shall turn the green spot on
for the time specified by the config-
ured value.
N/A N/A
Programming Mode - The following indications ONLY occur when the imager is in Programming Mode.
Label Programming
Mode Entry
A valid programming label has been
scanned.
LED blinks continuously
Imager sounds four low frequency
beeps.
Label Programming
Mode Rejection of
Label
A label has been rejected. N/A
Imager sounds three times at low-
est frequency & current volume.
Label Programming
Mode Acceptance
of Partial Label
In cases where multiple labels must
be scanned to program one feature,
this indication acknowledges each
portion as it is successfully
scanned.
N/A
Imager sounds one short beep at
highest frequency & current volume.
Label Programming
Mode Acceptance
of Programming
Configuration option(s) have been
successfully programmed via labels
and the imager has exited Program-
ming Mode.
N/A
Imager sounds one high frequency
beep and 4 low frequency beeps
followed by reset beeps.
Label Programming
Mode Cancel Item
Entry
Cancel label has been scanned. N/A
Imager sounds two times at low fre-
quency and current volume.
- QuickScan 1
- Table of Contents 3
- Chapter 1 9
- Introduction 9
- Manual Conventions 10
- References 10
- Technical Support 11
- 4 QuickScan® QD2100 12
- Chapter 2 13
- Getting Started 13
- Connecting at 14
- Disconnecting at 14
- Programming 15
- Select the Interface Type 16
- Configure Interface Settings 16
- Configure Other Features 16
- Standard Product Default Set 17
- 10 QuickScan® QD2100 18
- Chapter 3 19
- Interfaces 19
- Select RS-232 OPOS 20
- Configuring the Interface 21
- 14 QuickScan® QD2100 22
- Global Interface Features 23
- USB Suspend Mode 24
- Chapter 4 25
- General Features 25
- 18 QuickScan® QD2100 26
- Label Gone Timeout 27
- Label Gone Timeout — cont 28
- LED and Beeper Indicators 29
- Good Read: When to Indicate 30
- Good Read Beep Type 31
- Good Read Beep Frequency 32
- Good Read Beep Length 32
- Good Read Beep Volume 34
- Good Read LED Duration 35
- 2 seconds 36
- Scanning Features 37
- Scan Mode — continued 38
- Stand Mode Triggered Timeout 39
- 32 QuickScan® QD2100 40
- Scanning Active Time 41
- Scanning Active Time — cont 42
- Flash On Time 43
- Flash On Time — cont 44
- Flash Off Time 45
- Flash Off Time — cont 46
- Stand Mode Sensitivity 47
- Green Spot Duration 48
- Chapter 5 49
- RS-232 ONLY Interface 49
- Baud Rate — continued 50
- Data Bits 51
- Stop Bits 52
- Parity = None 53
- Parity = Even 53
- Parity = Odd 53
- Handshaking Control 54
- Chapter 6 55
- RS-232/USB-Com Interfaces 55
- Intercharacter Delay 56
- Intercharacter Delay — cont 57
- Beep On ASCII BEL 58
- Beep On Not on File 58
- ACK NAK Options 59
- ACK Character 60
- ACK Character — cont 61
- NAK Character 62
- NAK Character — cont 63
- ACK NAK Timeout Value 64
- ACK NAK Timeout Value — cont 65
- ACK NAK Retry Count 66
- ACK NAK Retry Count — cont 67
- ACK NAK Error Handling 68
- Indicate Transmission Failure 69
- Disable Character 70
- Disable Character — cont 71
- Enable Character 72
- Enable Character — cont 73
- 66 QuickScan® QD2100 74
- Chapter 7 75
- Keyboard Interface 75
- Country Mode 76
- Country Mode — continued 77
- Caps Lock State 79
- Send Control Characters 80
- Wedge Quiet Interval 81
- Wedge Quiet Interval — cont 82
- Intercode Delay 85
- Intercode Delay — cont 86
- USB Keyboard Speed 87
- 80 QuickScan® QD2100 88
- Chapter 8 89
- USB-OEM Interface 89
- USB-OEM Device Usage 90
- Chapter 9 91
- IBM 46XX Interface 91
- 46xx Number of Host Resets 92
- 86 QuickScan® QD2100 94
- IBM Standard Format — 95
- Code 39 Format — 95
- 88 QuickScan® QD2100 96
- Chapter 10 97
- 00 - 20 Characters (ASCII) 98
- Global Prefix/Suffix 99
- No Global Prefix 99
- Global Suffix = 0x0D (CR) 99
- Global AIM ID 100
- Global AIM ID — continued 101
- GS1-128 AIM ID 102
- Label ID 103
- 96 QuickScan® QD2100 104
- Data Editing 106
- Label ID — continued 107
- Case Conversion 115
- Character Conversion 116
- ENTER/EXIT PROGRAMMING MODE 117
- 110 QuickScan® QD2100 118
- Chapter 11 119
- Symbologies 119
- UPC-A Enable/Disable 120
- UPC-A — cont 121
- UPC-E Enable/Disable 123
- UPC-E — cont 124
- GTIN Formatting 127
- EAN 13 Enable/Disable 128
- EAN 13 — cont 129
- EAN-13 ISBN Conversion 130
- EAN 8 Enable/Disable 132
- EAN 8 — cont 133
- UPC/EAN Global Settings 135
- 128 QuickScan® QD2100 136
- UPC/EAN Correlation 137
- UPC/EAN Price Weight Check 138
- UPC-A Minimum Reads 139
- Optional Add-ons 140
- Add-Ons — cont 141
- GS1 DataBar Omnidirectional 151
- 144 QuickScan® QD2100 152
- GS1 DataBar Expanded 153
- GS1 DataBar Expanded — cont 154
- GS1 DataBar Limited 160
- GS1 DataBar Limited — cont 161
- Code 39 Enable/Disable 162
- Code 39 — cont 163
- Code 39 Stitching 178
- Code 32 Enable/Disable 179
- Code 32 — cont 180
- Code 128 181
- Code 128 — cont 182
- GS1-128 Enable 195
- Interleaved 2 of 5 (I 2 of 5) 196
- 190 QuickScan® QD2100 198
- I 2 of 5 Minimum Reads 199
- 2 of 5 Decoding Level 200
- 2 of 5 Decoding Level — cont 201
- I 2 of 5 Length Control 202
- I 2 of 5 Set Length 1 203
- 06 = Length 1 is 6 Characters 204
- I 2 of 5 Set Length 2 205
- I 2 of 5 Set Length 2 — cont 206
- I 2 of 5 Stitching 208
- Datalogic 2 of 5 209
- Datalogic 2 of 5 — cont 210
- 210 QuickScan® QD2100 218
- Codabar Enable/Disable 221
- Codabar — cont 222
- Codabar Stitching 238
- Code 11 Enable/Disable 239
- Code 11 — cont 240
- Code 11 Decoding Level 250
- Code 11 Stitching 253
- Standard 2 of 5 254
- Standard 2 of 5 — cont 255
- Standard 2 of 5 Stitching 263
- ISBT 128 264
- ISBT 128 — cont 265
- ISBT 128 Force Concatenation 265
- Code 4 Enable/Disable 266
- Code 4 — cont 267
- Code 5 Enable/Disable 268
- Code 5 — cont 269
- Code 4 and 5 Decoding Level 270
- 264 QuickScan® QD2100 272
- Follett 2 of 5 273
- 266 QuickScan® QD2100 274
- Appendix A 275
- 268 QuickScan® QD2100 276
- Standard Cable Pinouts 277
- 270 QuickScan® QD2100 278
- Appendix B 279
- Interleaved 2 of 5 284
- Default Exceptions 288
- Interface: RS232-OPOS 289
- 282 QuickScan® QD2100 290
- Appendix C 291
- LED and Beeper Indications 292
- Error Codes 293
- 286 QuickScan® QD2100 294
- Appendix D 295
- Sample Barcodes — continued 296
- Code 32 296
- Codabar 296
- Code 93 296
- Code 11 296
- GS1 DataBar (RSS) 297
- 290 QuickScan® QD2100 298
- Appendix E 299
- 292 QuickScan® QD2100 300
- 294 QuickScan® QD2100 302
- Appendix F 303
- Product Reference Guide 304
- Digital Interface 308
- Digital Interface — cont 309
- IBM31xx 102-key 310
- IBM31xx 102-key — cont 311
- IBM XT — cont 313
- 306 QuickScan® QD2100 314
- 308 QuickScan® QD2100 316
- Product Reference Guide 309 317
- 310 QuickScan® QD2100 318
- ASCII Chart 319
Related products and manuals for Bar code readers Datalogic Scanning QuickScan QD2100
(67 pages)
(44 pages)© 2020, manymanuals.com. All rights reserved. | 3.637 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals